今までが松下のLet's note R2にNetBSD 3.1系(3.0系だったかも)で使っていたが、とりあえずNetBSD4.0を使かった感想でも。
○ハード面
・dynabookの方が筐体がやわな感じがする。
・CPUファンがあるがかなり静かで、夜中にTVや暖房機など何も付けていなければ多少は音に気がつく程度。
・キーボードは打ちやすいかと。R2比べれば大きいこともあるかと。
・パームトップのボタンが堅い。
・電源コードが妙に長い。パソコンに指す部分がI型でじゃま。L型にしてほしい。
・PCカードスロットとDVDドライブが重なっているのでカードによっては干渉する。
・ディスプレイを閉めても留め具がないので少し不安。
・R2の1024x768からRX1の1280x800にすると画面が大きく感じる。ただ画面の収まりも悪いかも。
○ソフト面(GENERIC_LAPTOPカーネル)
・文字入力をkinput2+FreeWnnからuim+anthyに変更(SoftwareDesign2007.3参考)。
・GENERIC_LAPTOPカーネルでは無線LANが出てこない...
チップが4965ＡＧＮで良いのかな。そうするとNetBSD-currentdに対し2009.2.9にやってきたばかりか。
・標準のXFree86 4.5.0で1280x800を出すのにてこずる。
「Section "Device"」の 「Driver」は「"vesa"」とし、「Section "Monitor"」に
・HorizSync 28-89.0
・VertRefresh 50-70
・Modeline "1280x800" 67.26 1280 1312 1560 1592 800 817 824 841
を追加したら表示できた。とりあえずパラメータはここから取り出した。
・athなPCカードで「OFDM6」までしか安定せずに通信できなかったのがautoselectにしておいても安心に。
・有線LAN(wm)は素直に動いた。
・輝度調整は動かない。
・映像外部出力は未確認
・MP3は再生できたがmplayerで動画がうまく再生できない。
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 4.0 (GENERIC_LAPTOP) #0: Sun Dec 16 00:27:57 PST 2007
builds@wb34:/home/builds/ab/netbsd-4-0-RELEASE/i386/200712160005Z-obj/home/builds/ab/netbsd-4-0-RELEASE/src/sys/arch/i386/compile/GENERIC_LAPTOP
total memory = 2038 MB
rbus: rbus_min_start set to 0x80000000
avail memory = 1995 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfcb25
PCI BIOS rev. 2.1 found at 0xfd608
pcibios: config mechanism [1][x], special cycles [x][x], last bus 4
PCI IRQ Routing Table rev. 1.0 found at 0xf0230, size 160 bytes (8 entries)
PCI Interrupt Router at 000:31:0 (Intel 82371FB (PIIX) PCI-ISA Bridge compatible)
------------------------------------------
device vendor product pin PIRQ IRQ stage
------------------------------------------
000:02:0 0x8086 0x27a2 A 0x00 10 0 already assigned
000:27:0 0x8086 0x27d8 A 0x06 11 0 fixed up
000:28:0 0x8086 0x27d0 A 0x01 11 0 already assigned
000:28:2 0x8086 0x27d4 C 0x02 11 0 already assigned
000:29:0 0x8086 0x27c8 A 0x07 11 0 already assigned
000:29:1 0x8086 0x27c9 B 0x03 11 0 already assigned
000:29:2 0x8086 0x27ca C 0x02 11 0 already assigned
000:29:3 0x8086 0x27cb D 0x00 10 0 already assigned
000:29:7 0x8086 0x27cc A 0x07 11 0 already assigned
000:31:2 0x8086 0x27c5 B 0x03 11 0 already assigned
001:00:0 0x8086 0x109a A 0x00 10 0 already assigned
002:00:0 0x8086 0x4229 A 0x02 11 0 already assigned
003:11:0 0x104c 0x8039 A 0x05 11 0 fixed up
003:11:1 0x104c 0x803a B 0x04 11 0 fixed up
003:11:3 0x104c 0x803c D 0x07 11 0 fixed up
------------------------------------------
mainbus0 (root)
pci_addr_fixup: 000:02:1 0x8086 0x27a6 new address 0x7f800000
pci_addr_fixup: 000:27:0 0x8086 0x27d8 new address 0x7f880000
pci_addr_fixup: 003:11:0 0x104c 0x8039 new address 0x7f884000
pci_addr_fixup: 003:11:1 0x104c 0x803a new address 0x7f885000
pci_addr_fixup: 003:11:1 0x104c 0x803a new address 0x7f888000
pci_addr_fixup: 003:11:3 0x104c 0x803c new address 0x7f885800
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel Core 2 (Merom) (686-class), 1197.08 MHz, id 0x6f2
cpu0: features bfebfbff
cpu0: features bfebfbff
cpu0: features bfebfbff
cpu0: features2 e3bd
cpu0: "Intel(R) Core(TM)2 CPU U7600 @ 1.20GHz"
cpu0: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
cpu0: L2 cache 2 MB 64B/line 8-way
cpu0: using thermal monitor 1
cpu0: Enhanced SpeedStep (924 mV) 1200 MHz
cpu0: unknown Enhanced SpeedStep CPU.
cpu0: using only highest and lowest power states.
cpu0: Enhanced SpeedStep frequencies available (MHz): 1200 800
cpu0: 64 page colors
cpu at mainbus0: not configured
ioapic at mainbus0: not configured
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
ACPI-Safe 24-bit timer
mpacpi: could not get bus number, assuming bus 0
LNKA: ACPI: Found matching pin for 0.2.INTA at func 0: 10
LNKG: ACPI: Found matching pin for 0.27.INTA at func 0: 11
LNKB: ACPI: Found matching pin for 0.28.INTA at func 0: 11
LNKC: ACPI: Found matching pin for 0.28.INTC at func 2: 11
LNKH: ACPI: Found matching pin for 0.29.INTA at func 0: 11
LNKD: ACPI: Found matching pin for 0.29.INTB at func 1: 11
LNKC: ACPI: Found matching pin for 0.29.INTC at func 2: 11
LNKA: ACPI: Found matching pin for 0.29.INTD at func 3: 10
LNKD: ACPI: Found matching pin for 0.31.INTB at func 2: 11
LNKF: ACPI: Found matching pin for 3.11.INTA at func 0: 255
LNKE: ACPI: Found matching pin for 3.11.INTB at func 1: 11
LNKH: ACPI: Found matching pin for 3.11.INTD at func 3: 11
LNKA: ACPI: Found matching pin for 1.0.INTA at func 0: 10
LNKC: ACPI: Found matching pin for 2.0.INTA at func 0: 11
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C01 at acpi0 not configured
PNP0C02 at acpi0 not configured
PNP0A08 at acpi0 not configured
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
PNP0200 at acpi0 not configured
PNP0000 at acpi0 not configured
PNP0100 at acpi0 not configured
PNP0800 at acpi0 not configured
PNP0C04 at acpi0 not configured
PNP0303 at acpi0 not configured
PNP0F13 at acpi0 not configured
PNP0B00 at acpi0 not configured
PNP0C02 at acpi0 not configured
IFX0102 at acpi0 not configured
PNP0103 at acpi0 not configured
acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
acpibat0 at acpi0 (PNP0C0A-1): ACPI Battery (Control Method)
acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
acpiacad0 at acpi0 (ACPI0003): ACPI AC Adapter
TOS6208 at acpi0 not configured
TOS620A at acpi0 not configured
acpitz0 at acpi0: ACPI Thermal Zone
acpitz0: unable to get polling interval; using default of 30.0s
acpitz0: passive cooling mode only
acpitz0: critical 102.0C
apm0 at acpi0: Power Management spec V1.2
acpibat0: battery info: (null), Li-ION , G71C00086510, 0000000369
acpiacad0: AC adapter online.
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82945GM/PM/GMS Host Bridge (rev. 0x03)
agp0 at pchb0: detected 7932k stolen memory
agp0: aperture at 0xe0000000, size 0x10000000
vga1 at pci0 dev 2 function 0: Intel 82945GM/PM/GMS Integrated Graphics Device (rev. 0x03)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
Intel 82945GM/PM/GMS Integrated Graphics Device (miscellaneous display, revision 0x03) at pci0 dev 2 function 1 not configured
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia0: interrupting at irq 11
azalia0: host: Intel 82801GB/GR High Definition Audio Controller (rev. 2)
azalia0: host: High Definition Audio rev. 1.0
ppb0 at pci0 dev 28 function 0: Intel 82801GB/GR PCI Express Port #1 (rev. 0x02)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
wm0 at pci1 dev 0 function 0: Intel i82573L Gigabit Ethernet, rev. 0
wm0: interrupting at irq 10
wm0: PCI-Express bus
wm0: 256 word (8 address bits) SPI EEPROM
wm0: Ethernet address 00:15:b7:c5:a8:f2
makphy0 at wm0 phy 1: Marvell 88E1111 Gigabit PHY, rev. 2
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb1 at pci0 dev 28 function 2: Intel 82801GB/GR PCI Express Port #3 (rev. 0x02)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
Intel product 0x4229 (miscellaneous network, revision 0x61) at pci2 dev 0 function 0 not configured
uhci0 at pci0 dev 29 function 0: Intel 82801GB/GR USB UHCI Controller (rev. 0x02)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801GB/GR USB UHCI Controller (rev. 0x02)
uhci1: interrupting at irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801GB/GR USB UHCI Controller (rev. 0x02)
uhci2: interrupting at irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3: Intel 82801GB/GR USB UHCI Controller (rev. 0x02)
uhci3: interrupting at irq 10
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801GB/GR USB EHCI Controller (rev. 0x02)
ehci0: interrupting at irq 11
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb2 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0xe2)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled
cbb0 at pci3 dev 11 function 0: Texas Instruments product 0x8039 (rev. 0x00)
Texas Instruments product 0x803a (Firewire serial bus, interface 0x10) at pci3 dev 11 function 1 not configured
Texas Instruments product 0x803c (SD Host Controller system, interface 0x01) at pci3 dev 11 function 3 not configured
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 4
pcmcia0 at cardslot0
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801GBM LPC Interface Bridge (rev. 0x02)
ahcisata0 at pci0 dev 31 function 2: Intel 82801GBM AHCI SATA Controller
ahcisata0: interrupting at irq 11
ahcisata0: AHCI revision 1.1, 4 ports, 32 command slots, features 0xc710e000
atabus0 at ahcisata0 channel 0
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
pcppi0: children must have an explicit unit
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
pcppi0: attached to attimer0
isapnp0: no ISA Plug 'n Play devices found
WARNING: Callback scheduled before sysmon task queue thread present.
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: Realtek ALC262 (rev. 1.0)
azalia0: codec[0]: High Definition Audio rev. 1.0
azalia0: playback: max channels=2, encodings=1
azalia0: playback: PCM formats=e0560<24bit,20bit,16bit,192kHz,96kHz,48kHz,44.1kHz>
azalia0: recording: max channels=2, encodings=1
azalia0: recording: PCM formats=60160<20bit,16bit,96kHz,48kHz,44.1kHz>
audio0 at azalia0: full duplex, independent
Kernelized RAIDframe activated
ahcisata0 port 0: device present, speed: 1.5Gb/s
wd0 at atabus0 drive 0:
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
ath0 at cardbus0 function 0
ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: mac 5.6 phy 4.1 5 GHz radio 1.7 2 GHz radio 2.3
umass0 at uhub4 port 4 configuration 1 interface 0
umass0: TOSHIBA Optical Drive Controller, rev 2.00/0.00, addr 2
umass0: using ATAPI over Bulk-Only
atapibus0 at umass0: 2 targets
ugen0 at uhub1 port 1
ugen0: AuthenTec Fingerprint Sensor, rev 1.10/c.10, addr 2
cd0 at atapibus0 drive 0:
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
ath0: interrupting at 255
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
mplayerは「-vo x11」オプションをつけたら再生できた。だけど今度はサイズ変更が。先は長いかな
返信削除